Bentley Continental Key Fob Troubleshooting Tips
The Bentley Continental is an incredibly amazing car to drive. Its brushed-metal accents the center stack and gorgeous wood and leather decorate its interior. Its powerful W12 engine is able to produce 552 break horse power.
The Continental key fob is encased with rubber to protect water from destroying the electronic chip. If it gets submerged in clean tap water or rain it is fine, but prolonged exposure to salty water could damage it.
Keyless entry system
The Bentley Continental comes with a keyless entry system, which allows you to lock and unlock your vehicle using remote controls. This is convenient and helps you save time and effort. However, there are many reasons for why your key fob might not function properly. One of them is a dead battery or water damage, as well as receiver module issues. In some instances a malfunctioning internal chip could be the reason for the issue.
The key fob is fitted with rubber seals to prevent water from reaching the electronic chips inside. However, the key fob could be wet if exposed to salty or soapy water. This could cause damage to the chip. It is essential to allow the key fob to dry completely before replacing the battery. If the key fob doesn't function after drying and cleaning, it is probably faulty and requires replacement.
The clips made of metal on the battery of your Continental keyfob keep it in place and complete the circuit. If the clips become loose or corroded, they could cause contact issues. Check the battery's contacts to make sure they are clean. Make sure the battery is firmly inserted. If you have a spare Continental key, try it to determine if it is working. If the key is faulty, you can try to reprogram it using an OBDII scanner.
Battery
The key fob has a tiny coin battery within. If the battery is dead, the remote won't work. It is easy to find out the cause and replace the battery in a matter of minutes. Water can also harm the battery, requiring a replacement. The key fob might not function for a variety of reasons, including worn-out buttons, damaged contacts in the battery, signal interference or an inactive module. You can reset the system if you disconnect the 12 voltage batteries for a couple of moments. This will allow the system itself to reset. Connect the positive cable first, then disconnect the negative cable.
The battery in the Bentley Continental key fob will last for up to four years based on the frequency you use it. The battery comes with metal retaining clips that keep it in place and complete the circuit. The clips should be tight however if they're not the remote won't function properly.
If the Continental key fob is exposed to clean tap water, it should be cleaned with a paper towel and allowed to dry before putting it back into the battery. If the chip is exposed to soapy or salty water, it might be damaged. In these instances you'll need to buy an entirely new key fob.
Water damage
David does not believe there are any major mechanical issues on this Continental. There is some surface corrosion on the wheels where they were exposed to road grit. The boot is roomy and practical with an original warning triangle strapped to the floor, plus a space-saver spare wheel and the basic Bentley toolkit under the false floor.
The chip inside the key fob is protected by rubber seals that should keep it in operation even if the water is puddled. However long-term exposure to water can harm the chip, so it is recommended to take your key fob out of your pockets when you go swimming, kayaking and rafting, canyoning or other activities where it may get wet.
If your key fob was submerged in water or soapy water, you can still try to save it. Use electronic cleaners or isopropyl ethanol to clean the chip. If your key-fob doesn't work after cleaning and drying it then you may have to replace it. If you're in the market for a Bentley Continental key fob, be sure to select one that's waterproof and fitted by the factory to your car.
Fault diagnosis
The Bentley Continental keyfob permits you to lock or unlock your vehicle with just one click. This system is very convenient and provides safety and security when driving. However there are a few things that can cause problems with your key fob. The most frequent causes include a dead coin battery or signal interference, water damage or a malfunctioning internal chip. There are a few troubleshooting techniques you can try to find out the reason for a key fob that is not working.
The first thing you need to look at is the battery. Make sure that it is securely inserted and that the metal retaining clips are correctly positioned. If the clips aren't in a good position, the battery may not have a proper contact and will not function properly. The clips used to hold them must be free of corrosion and clean.
bentley leather key case The Key Lab that is weak is a different reason for the key fob to not function. The 12 volt Continental battery should be in good health to communicate with your remote keyless entry system, as well as the rest of the onboard electronics. Examine the fuses, and if needed, recharge your battery.
The Bentley Continental key fob sends signals to the receiver module which is located within the ignition barrel. If the signal is not received the engine will not start and the alarm will go off. If the Bentley Continental key fob isn't working, then you should talk to a professional.